JTAG-HS3, FT232 chip erased

[twister]

Hello, I have used the digilent JTAG-HS3 programmer simultaneously with other device with FT232H chip and I have probably erased by accident the FT232 chip on Digilent module or there is a problem with drivers - the device is still recognized as Digilent USB serial converter by the system so I think is not damaged, but the cable is not visible in xilinx software. Could you please help me?

[Sergey]

Hi

I have also erased the EPROM of my JTAG HS3 programmer. Given how often it happens, why not release the EPROM image publicly?  

Thanks and regards

[David Fenger]

Yet another case here, I suspect.  My JTAG-HS3 Rev.A stopped working abruptly today (no longer seen by Vivado) after years of loyal service. 

It still connects as a USB device, and shows up as a USB Serial Converter in Hardware Manager, but it's using the FTDI driver, and VID 0403, PID 6014.

[mattiacorp]

Hello.

Accidentally erased the contents of the EEPROM JTAG-HS3 how to recover the board. Vivado does not work

[JColvin]

Hi @mattiacorp,

I have sent you a PM with some instructions.

Thanks,
JColvin

[Tiago Goncalves]

I have used a JTAG-HS3 while using FT_Prog to program another FTDI device and the HS3 stopped working. Can you share the recovery procedure?

[JColvin]

Hi @Tiago Goncalves,

I have sent you a PM with some instructions.

Thanks,
JColvin

[LAlfaro]

Hello all,

@JColvin, it looks like I also have had the same issue as the others. After programming an FT232H with ft_prog, my JTAG-HS3 stopped working. Could you please help me?

Thanks in advance. 

[JColvin]

Hi @LAlfaro,

I have sent you a PM.

Thanks,
JColvin

[K.Okada]

Hi,

I also accidentally erased the eeprom on my JTAG-HS3. Please tell me how to recover the eeprom?

Edited June 7, 2023 by K.Okada

[JColvin]

Hi @K.Okada,

I have sent you a PM.

Thanks,
JColvin

[vectro121]

Hi @JColvin,

Could you please send me the restore instructions/data? I urgently need it.

Thanks

[JColvin]

Hi @vectro121,

I have sent you a PM.

Thanks,
JColvin

[gianluca88]

Hello,

accidentally erased the contents of the EEPROM JTAG-HS3. Vivado does not work.

Can i recover the board?

Tnx

[JColvin]

Hi @gianluca88,

I have sent you a PM.

Thanks,
JColvin

[Arye]

Hi, 

I also have such issue on our xilinx kcu116 evb board, on your module on this evb, how can I reprogram it? 

[Svyat96]

Hello, @JColvin

   Same here, any chance you can send me the file to reprogram?   Thanks

[Sahko]

Hello,

 

I also have this problem where the HS3 is no longer detected by the Xilinx ISE software, the firmware has been cleared from the ft232 can someone help we with this?

 

Thank you, Alex G.

[Bonand]

Hello,

probably I have the same problem because my JTAG-HS3 stop to working after some years that is unused.

How can I restore it to fectory settings?

Thanks.

[JColvin]

I have sent some PMs.

Thanks,
JColvin

[MicNZh]

Hello, @JColvin

It looks like I also have had the same issue. After programming an FT4232HL with ft_prog, my SMT4 Programmer stopped working. Could you help me?

Thanks.

 

[JColvin]

Hi @MicNZh,

I have sent you a PM.

Thanks,
JColvin

[craigec]

Hello,

I also have the same problem -  used FT_Prog to program another FTDI device and the JTAG-HS3 which was connected was overwritten by mistake. Can you help please?

[JColvin]

Hi @craigec,

I have sent you a PM.

Thanks,
JColvin

[anatolianboy]

On 8/13/2020 at 12:36 PM, aivark6 said:

Hi

I guess I have the same problem. I've been using 3 digilent JTAG-HS3 programmers simultaneously and one of those FT232H chips has probably been erased by accident. I used FT Prog to check the device and I can see following.

EEPROM seems to be missing and properties are missing Digilent values.

Thanks

I have same problem. How can i fix it?

[JColvin]

Hi @anatolianboy,

I have sent you a PM.

Thanks,
JColvin