JTAG-HS3, FT232 chip erased

[twister]

Hello, I have used the digilent JTAG-HS3 programmer simultaneously with other device with FT232H chip and I have probably erased by accident the FT232 chip on Digilent module or there is a problem with drivers - the device is still recognized as Digilent USB serial converter by the system so I think is not damaged, but the cable is not visible in xilinx software. Could you please help me?

[GreenbackBoogie]

Hi,

I am having the same problem for my JTAG HS3 boards that were probably erased while programming other FTDI chip connected.

Please help, I had 3 cables and only realized now to search forums.

[JColvin]

Hi @GreenbackBoogie,

I have sent you a PM about this.

Thanks,
JColvin

[aivark6]

Hi

I guess I have the same problem. I've been using 3 digilent JTAG-HS3 programmers simultaneously and one of those FT232H chips has probably been erased by accident. I used FT Prog to check the device and I can see following.

EEPROM seems to be missing and properties are missing Digilent values.

Thanks

[JColvin]

Hi @aivark6,

I have sent you a PM about this.

Thanks,
JColvin

[Dm77]

Hello.

Accidentally erased the contents of the EEPROM JTAG-HS3 how to recover the board. Vivado does not work

[JColvin]

Hello @Dm77,

I have sent you a PM about this.

Thanks,
JColvin

[Marco Jassmann]

Hello,

we also have potentially erased by an accident the Firmware.

Can you please send me the Firmware with the instructions, too ?

 

Best Regards

Marco

[JColvin]

Hi @Marco Jassmann,

Is this also with the JTAG HS3?

Thanks,
JColvin

[Marco Jassmann]

Hi @JColvin,

yes, it is the JTAG HS3.

It was potentially attached on the USB -Hub while we programmed an other FDTI based device.

Best regards

Marco

[JColvin]

Hi @Marco Jassmann,

I apologize for the delay. I have sent you a PM.

Thanks,
JColvin

[namn]

Hi @JColvin,

 

I mistakenly reprogrammed the FTDI of my JTAG HS3, rendering it unusable (was trying to program another FTDI). Now I can not use it anymore and it does not show up in any of my software tools. How to fix? Thanks for help!

 

Best Regards

 

Namn

[JColvin]

Hi @namn,

I have sent you a PM.

Thanks,
JColvin

[James783]

I have also mistakenly reprogrammed the FTDI of my JTAG HS3, please can you send me the instructions to re program the EEPROM. BR

[JColvin]

Hi @James783,

I have sent you a PM.

Thanks,
JColvin

[benitoss]

Hi

I have erased the EPROM of my JTAG HS3 programmer, please could anybody tell me how to re-program it ???

Thanks and regards

[JColvin]

Hi @benitoss,

I have sent you a PM.

Thanks,
JColvin

[Nickm]

Hello,

   Same here, any chance you can send me the file to reprogram?   Thanks

[JColvin]

Hi @Nickm,

I have sent you a PM.

Thanks,
JColvin

[jonoli6309]

Hello,

I think I have my programmer rendered unusable by accidentally running the FT_Prog EEPROM Programming Utility on my Computer.

Would you mind to send me the reprogram file? Sincerely thanks.

Also sorry for my poor English as I am not a native speaker.

[jonoli6309]

On 5/9/2021 at 6:30 PM, jonoli6309 said:

Hello,

I think I have my programmer rendered unusable by accidentally running the FT_Prog EEPROM Programming Utility on my Computer.

Would you mind to send me the reprogram file? Sincerely thanks.

Also sorry for my poor English as I am not a native speaker.

@JColvin

[JColvin]

Hi @jonoli6309,

Which board are you using?

Thanks,
JColvin

[jonoli6309]

On 5/18/2021 at 12:37 AM, JColvin said:

Hi @jonoli6309,

Which board are you using?

Thanks,
JColvin

As far as I know, it's a SMT4 Programmer which belongs to my college.

[JColvin]

Hi @jonoli6309,

I'll have to ask about this; the material that I have does not have support for the SMT4.

Thanks,
JColvin

[JColvin]

Hi @jonoli6309,

I should have access to the materials I need to "reset" the SMT4 tomorrow once I don't encounter errors trying to connect to the corporate network from my home computer.

Thanks,
JColvin

[Bianca]

@jonoli6309,

I sent you the solution in our previous opened DM.

Regards,

Bianca