TKMoon Posted October 9, 2019 Share Posted October 9, 2019 Hi My OpenLogger stopped with Orange LED turn on. This means 'Device is booting and not ready to use. (https://reference.digilentinc.com/reference/instrumentation/openlogger/openlogger-hardware-implementation-details) I manually re-downloaded firmware to v1.3.0 but still stopped during booting. (https://reference.digilentinc.com/reference/instrumentation/openlogger/recover-from-corrupt-firmware) I connected putty to check a booting message, and it was as following (https://forum.digilentinc.com/topic/17533-open-logger-initial-firmware-update-failed/?tab=comments#comment-44355) Error A000001B happens during booting. How Can I solve thie AutoConnect fail? Sincerely. Link to comment Share on other sites More sharing options...
AndrewHolzer Posted October 9, 2019 Share Posted October 9, 2019 Hi @TKMoon, The error code you have there signifies no networks found. This error alone shouldn't cause the device to never finish booting however. To solve the AutoConnect error you must either bring the network back up or have the device forget the network configuration information. Can you tell me how long you've had the device and anything that may have happened leading up to the device failing to boot? Regards, AndrewHolzer Link to comment Share on other sites More sharing options...
TKMoon Posted October 9, 2019 Author Share Posted October 9, 2019 6 hours ago, AndrewHolzer said: Hi @TKMoon, The error code you have there signifies no networks found. This error alone shouldn't cause the device to never finish booting however. To solve the AutoConnect error you must either bring the network back up or have the device forget the network configuration information. Can you tell me how long you've had the device and anything that may have happened leading up to the device failing to boot? Regards, AndrewHolzer Hi @AndrewHolzer I bought OpenLogger last wek for project, and It happened my 1st day using. During configuration, Once I connected Logger to WiFi, but soon I deleted the setting. I had a problem with logging to SD card with standalone operation. The log file kept 0B even I turned on 10 minutes. I set 'Log on Boot' flag and ' Log to 'SD' , and saved settings to a new profile. So, I tried to change other settings over and over, then this happened Sincerely. TKMoon Link to comment Share on other sites More sharing options...
vicentiu Posted October 16, 2019 Share Posted October 16, 2019 Did you press the PROG button to flush out the data to the SD card before removing it as described here? Link to comment Share on other sites More sharing options...
TKMoon Posted October 22, 2019 Author Share Posted October 22, 2019 On 10/16/2019 at 6:59 PM, vicentiu said: Did you press the PROG button to flush out the data to the SD card before removing it as described here? No, I'll try this after the board get works. Thank you, Vincentiu. My OpenLogger MZ still can't enter into normal mode. (Yellow lamp on) Link to comment Share on other sites More sharing options...
TKMoon Posted October 22, 2019 Author Share Posted October 22, 2019 On 10/10/2019 at 8:54 AM, TKMoon said: Hi @AndrewHolzer I bought OpenLogger last wek for project, and It happened my 1st day using. During configuration, Once I connected Logger to WiFi, but soon I deleted the setting. I had a problem with logging to SD card with standalone operation. The log file kept 0B even I turned on 10 minutes. I set 'Log on Boot' flag and ' Log to 'SD' , and saved settings to a new profile. So, I tried to change other settings over and over, then this happened Sincerely. TKMoon Is there any way to fix this? or, I want refund or change to new one. I even could not connected to any devices to monitor... Link to comment Share on other sites More sharing options...
vicentiu Posted October 22, 2019 Share Posted October 22, 2019 When you reflashed the firmware, did you see Success confirmation like this? Link to comment Share on other sites More sharing options...
TKMoon Posted October 22, 2019 Author Share Posted October 22, 2019 12 minutes ago, vicentiu said: When you reflashed the firmware, did you see Success confirmation like this? Yes. 1) I tried to connect with agent, but not connected 2) I chose the device to load a latest F/W but this did not work. 3) So, I set to 'other' version and selected 'OpenLoggerMZ-1.3.0.hex' downloaded from reference center https://reference.digilentinc.com/reference/instrumentation/openlogger/start 4) I set the logger into boot mode (keep pushing Prog button during I push a Reset button) Red LED blinking. 5) After I push 'FLASH SELECTED FIRMWARE' button, the progress bar goes to up to 100% and shows 'Successful!' 6) I reboot a device and tried to connect, but still do not work. Link to comment Share on other sites More sharing options...
Bianca Posted October 22, 2019 Share Posted October 22, 2019 Hello @TKMoon, You have a private message regarding this issue. Best regards, Bianca Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.