David Blu

OK Is it possible to connect the analog discovery 2 module with the raspberry pi 4??? From that arrangement could we develop an embedded systems from that arrangement ??? thanks, David Blubaugh

Thank You for timely response !!! I greatly appreciate it !!! OK I do have one more question. In regards to the Analog Discovery 2 module itself. IS IT POSSIBLE to develop a C/C++, C#, or Python program that controls the functionality of the Analog Discovery 2 module and then be able to download that same program written in either C/C++, C#, or Python into the actual Analog Discovery 2 module itself. IN A WAY, turning the Analog Discovery 2 module into an self-controlled embedded system without the need of the waveforms environment. I know one can develop programs on the laptop that then controls the Analog Discovery 2 module, but is it possible to then download that same program into the actual analog discovery 2 module itself thus creating a FPGA powered embedded system.. Is any of this possible??? If this is possible, could one also store and later process data points of oscilloscope capture points acquired by the Analog Discovery 2 module acting in the form of an embedded systems device??? Thank you once again for all of your help. Respectfully, David Blubaugh

OH I apologize. I made a mistake... The -5.0 volt to +5.0 volt was meant for the analog connections with a ground. The digital lines are only (0 volts or ground) to +5.0 volts. Is this electrically compatible ?? Please forgive my mistake !!! Respectfully, David Blubaugh

THANK YOU FOR YOUR RESPONSE JColvin !!! I greatly appreciate it !!! Looking at your detailed answer now !!! GREAT WORK !!! David

To whom it may concern, I am in the process of developing connections between a custom made potentio-stadt board that I am creating for a customer. We are deeply concerned that we could inadvertently destroy our newly purchased Analog Discovery 2 module that we have connect to this costumed made potentio-stadt board. The Connections between our costumed made potentio-stadt board and the Analog Discovery 2 module are as follows: POTENTIO-STADT BOARD IS CONNECTED TO THE ANALOG DISCOVERY 2 MODULE: START OF ANALOG CONNECTIONS------------------------------------------------------------------------------------------------------- UNIPOLAR DAC VOLTAGE POTENTIAL (0-3.3 VOLTS) CONNECTS -------------- > YELLOW WIRE ON WAVEFORM ONE (W1) UNIPOLAR DAC ONE OFFSET (0-3.3 VOLTS) CONNECTS --------------- > YELLOW-WHITE WIRE ON WAVEFORM TWO (W2) BIPOLAR REFLECTOR SW6 CONNECTS ---------------- > BLUE WIRE OR OSCILLISCOPE CHAN 2 (2+). BIPOLAR GROUND FOR REFLECTOR SW6 CONNECTS ----------------- > BLUE-WHITE WIRE OR OSCILLISCOPE CHAN 2 (2-) BIPOLAR CURRENT-OUT-VOLTAGE CONNECTS ----------------- > ORANGE WIRE OR OSCILLISCOPE CHAN 1 (1+) GROUND CONNECTS ----------------- > ORANGE-WHITE OR OSCILLISCOPE CHAN (1 -) END OF ANALOG CONNECTIONS-------------------------------------------------------------------------------------------------------- START OF DIGITAL CONNECTIONS------------------------------------------------------------------------------------------------------- RELAY SWITCH CONNECTS -------------------> GREEN WIRE OR 5 I/O (-5 TO 5.0 VOLTS) PIN A0 CONNECTS ----------------------> PURPLE WIRE OR 6 I/O (-5 TO 5.0 VOLTS) PIN ENABLE CONNECTS -----------------> BROWN WHITE WIRE OR 15 I/O (-5 TO 5 VOLTS) A1 CONNECTS --------------------> BROWN WIRE OR 7 I/O (-5 TO 5.0 VOLTS). A2 CONNECTS --------------------> PURPLE-WHITE WIRE OR 14 I/O (-5 TO 5.0 VOLTS). AO, ENABLE, A1, AND A2 ARE APART OF A MULTIPLEXER CIRCUIT. END OF DIGITAL CONNECTIONS------------------------------------------------------------------------------------------------------- Also, there has been a patchboard made by connecting all of the following ground connections such as 1- for oscilliscope chan one, 2- for oscilliscope chan two, and all of the ground connection pins on the Analog Discovery 2 module have all been connected to a common ground point on the project potentio-stadt board which is the ground point. Is this allowed or will this cause destruction to either the potnetio-stadt board we are constructing or cause desctruction to the analog discovery 2 module??? Please help us resolve this potential lethal problem and issue. Respectfully, David Blu