Search the Community

Showing results for tags 'qspi'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Test and Measurement
    • Measurement Computing (MCC)
    • Add-on Boards
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions
    • Archived

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 4 results

  1. Hello, I tried posting this on the Xilinx forums but got no response. These forums look more active and friendly so hopefully somebody can help me. I am really stuck. I am trying to follow along with the "How To Store Your SDK Project in SPI Flash" tutorial (https://reference.digilentinc.com/learn/programmable-logic/tutorials/htsspisf/start), but I cannot get it to work. I am using an Artix-7 35T Arty FPGA Evaluation Kit. I am running Vivado v2017.2 (64-bit) and SDK v2017.2 on a Windows 10 machine. First, I created a simple "Hello World" program by following the steps in the "Arty - Getting Started With Microblaze" tutorial ( https://reference.digilentinc.com/learn/programmable-logic/tutorials/arty-getting-started-with-microblaze/start). The only deviation from the instructions that I made was that after adding the MIG to the board, I added an AXI Quad SPI, with enabled port SPI_0, and then ran "Run Connection Automation". When I ran my C program on the Arty board it worked fine, and printed "Hello World" to my PuTTY terminal. I've attached my board file as both .bd and .png. Second, I tried store this "Hello World" program to the Arty's SPI Flash using the "How To Store Your SKD Project in SPI Flash" tutorial. But, it did not work. I'll walk you through what I did because there are a few things that I am confused about. Unless otherwise noted I followed the instructions exactly. Before step 0: I don't know what the QSpi mode jumper setting is referring to, so I didn't do anything. Step 1.3: I compressed my bitstream so I left FLASH_IMAGE_BASEADDR as 0xF8000000, like I found it. Steps 2.1 and 2.2: I used my "Hello World" app that I created by following the "Arty - Getting Started with Microblaze" tutorial. I couldn't place the sections into mig_7series_0 because that wasn't an option, so instead I used mig_7series_0_memaddr. Step 4.1: I used offset 0xF8000000 because that is what I used in Step 1.3. One other thing: the test says to use Arty flash type mt25ql128-spi-x1_x2_x4 (which I do), but the image of the "Program Flash Memory" window shows them using Arty flash type n25ql128-spi-x1_x2_x4. Step 5: it doesn't work. Does anyone have any suggestions? Is the SPI Flash some sort of external hardware that I need to plug into the Arty? Thanks in advance. design_1.bd
  2. Hi, My setup is using Avnet Ultrazed board with PMOD AD1. Also I am using Xilinx Vivado & SDK 2019.1. I am successfully being able to use 1 channel of the PMOD AD1. I am trying to use both the ADC channels on the PMOD AD1. As the PMOD libraries has no board support files for the Avnet Ultrazed board I went ahead and created a QSPI IP block to get a single channel working. I am having trouble getting the second channel working. Few doubts I have are: 1. For the QSPI IP block, should I use it in standard mode or Dual SPI mode. (I have set the data pins as MISO. Also selected the number of slaves as 1) 2. In the C code how do I switch between the 2 ADC channels as the 2 slaves are connected to the same chip select. I have set the slave select in initialize as --> XSpi_SetSlaveSelect(SpiInstancePtr, 0x01); 3. Should I use manual slave select or automatic slave select? --> XSpi_SetOptions(SpiInstancePtr, XSP_CLK_ACTIVE_LOW_OPTION | XSP_MASTER_OPTION | XSP_MANUAL_SSELECT_OPTION); Thanks!
  3. Dear all, I'm using Vivado 2018.3 and a Zybo Z7010 board. I have finally finished my project (I actually owe this forum much), and I am now trying to use the board without having to open nor Vivado neither the SDK. Basically, I know that I can program the QSPI flash memory of the board so that the program can run without having to upload it. How this works is still unclear, is switching from JTAG to QSPI enough or should I do something on Vivado? However, I am also using the Zynq processor which runs an application that I start from the SDK. Can I avoid opening the SDK? The better thing would be if I could programm the FPGA through Matlab but I don't know if this is possible. Could you point me to some tutorials or the matlab functions (if they exist...). Thank you very much, NotMyCupOfTea
  4. Hi, I am working on a project where i'm using Digilent zybo AP SoC with xilinx vivado for Hardware design and Xilinx SDK for software design. My application uses following protocol/peripherals: 1. UARTns16550 PL side (Programmable Logic) in interrupt mode. 2. GPIOs 3. Ethernet mac (lwIP stack) I started my software design using xilinx lwip perf client application project. Then i started modifying the perf client C code according to my need. My project contains Uartns16550, tcp/ip server and client program which receives real-time data. So coming to my problem, i am able to run my application from xilinx sdk GDB and system debugger. But, when i dump my code in QSPI flash and try to boot, the zybo is not booting up. I also tried loading different application project like tcp perf server, perf client. By doing this the processor boots up properly through QSPI flash. I followed the steps provided by Digilent for programming the flash and i also ensured that the jumpers are in the right place where it has to be. I believe that there's a problem with my program since i have started modifying the tcp perf client code for my project. I am not getting a clue where my code is going wrong. Operating System : Windows 10 Software : Xilinx vivado 2018.3/SDK 2018.3 Any inputs related to this will be appreciated. Thanks & Regards Ajeeth kumar