Search the Community

Showing results for tags 'ddr3'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Test and Measurement
    • Measurement Computing (MCC)
    • Add-on Boards
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions
    • Archived

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 4 results

  1. hello, i'm trying to simulate the mig controller to test calibration>write>read operation. i'm using MT41J128M16xx-125 memory and ZYBO-020 board. in simulation calibration is complete at 104us (nit_calib_complete =1) but and not able to receive the input data (app_wdf_data[127:0]) at the output pin (app_rd_data[127:0]) i check the vivado design example, in that also output data is random (as per me). so anyone please help me with this what've i done so far:- instantiate the mig_7series_0 in a top module copy the sim_tb_top (test bench in example design) and instantiate the top module with all files like u_delay and ddr3_module. that's it. very basic (now in simulation console i gave all the inputs and checking for the output after calibration, but i'm not able to receive the correct output. thank you.
  2. Hi, I am very new at field of FPGA. Now I am working Genesys2. I have to control DDR3 memory. I find some examples in Digilent site for DDR3 using microblaze processor. But, in my case I don't have to use microblaze processor. I have to send some fixed value through the DDR3 memory like 8-bit data (X'FF') i.e. I will write that data into the Genesys2 DDR3 memory and readout the data from the memory. I already go through Xilinx manual ug_586 . But still it is not clear to me how to start coding for the DDR3 memory. My questions are: 1) Is it possible to have example code without using microblaze processor for DDR3 memory? Or any suggestion for starting code to control DDR3 memory. Actually, I have do it in any way. So any helpful suggestion will be appreciated. Thank you.
  3. I'm at a complete loss trying to get the Arty A7-100t onboard DDR-SDRAM to behave reliably. Let me start by telling you what I've done (maybe some of this will be helpful for others): The Arty A7-100t is running totally unmodified (no PMOD, ChipKit, etc.). I've generated a Memory Interface Generator (MIG) IP core as per Digilent's recommendations: Digilent MIG Resources My XCI and PRJ files: ddr_sdram_mig.xci and ddr_sdram_mig.prj I've written a simple DDR SDRAM Interface module, based on the approach found on Numato. Unlike the reference code, my Verilog reads incoming addresses and reads / writes to RAM (or at least it should): ddr-sdram-interface.v I continually read from the aforementioned memory interface via the following code: always @(posedge clk_100mhz) begin if (readReady) begin readAddr <= readAddr + 1; end end assign led = readData[7:0]; I write to the memory (first all zeros, then all ones, then the address) via the following code: always @(posedge clk_100mhz) begin if (writeReady) begin writeAddr <= writeAddr + 1; if ((writeAddr == 0) && (writeCounter < 3)) begin writeCounter <= writeCounter + 1; end case (writeCounter) 0: writeData <= 32'h00000000; 1: writeData <= 32'h11111111; 2: writeData <= {8'h00, writeAddr}; 3: writeEn <= 0; endcase end end Now for the problem: If I run the Verilog above exactly as-is, the LEDs show total garbage (randomness). If, instead, I continually write (the same) data to memory over-and-over again, eventually the LEDs will start flashing the binary counter I expect. This tells me that the read mechanism is functional, but the write is extremely unreliable. Any insight would be most appreciated. I purchased the Arty A7-100t in part because it has the DDR3 memory. I understand that there are significant performance issues (due to the -1 speed grade of the Artix-7 chip), but I expect to be able to attain reliable read / write behavior at low-speed.
  4. Hello, I am using Arty7 board and I am strugglling with DDR3 RAM in Microblaze. I added to my design UART core Mig7 series core. Also, I have data set to write the DDR3 RAM after writing operation I will read these data set. Unfortunately, I couldnt upload into the DDR3 ram that data set. How can handle with thise issue? Can you help me?