Search the Community

Showing results for tags 'blinky'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Test and Measurement
    • Measurement Computing (MCC)
    • Add-on Boards
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions
    • Archived

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 2 results

  1. Hello all, I bought the nexys 100T , and since I am new I started with the basic tutorial blinky. Everything goes well until I get to step 8. "Synthesis, Implementation, and Bitstream Generation" The Synthesis ran successfully, and where it fails is at the bitstream generation. Since the Synthesis was completed I am assuming is not the verilog code, and is just some setting that I need to complete. The log gives the following in "Message:" (attached) Please help this is like the most frustrating hello world I ever had to do. I attached my project files and constrain files in case anyone wants to look at it. blinky.xpr Nexys-A7-100T-Master.xdc
  2. Hello all, I bought the nexys 4 DDR, and since I am new I started with the basic tutorial blinky. Everything goes well until I get to step 8. "Synthesis, Implementation, and Bitstream Generation" The Synthesis ran successfully, and where it fails is at the bitstream generation. Since the Synthesis was completed I am assuming is not the verilog code, and is just some setting that I need to complete. The log gives the following error: ERROR: [DRC NSTD-1] Unspecified I/O Standard: 2 out of 2 logical ports use I/O standard (IOSTANDARD) value 'DEFAULT', instead of a user assigned specific value. This may cause I/O contention or incompatibility with the board power or connectivity affecting performance, signal integrity or in extreme cases cause damage to the device or the components to which it is connected. To correct this violation, specify all I/O standards. This design will fail to generate a bitstream unless all logical ports have a user specified I/O standard value defined. To allow bitstream creation with unspecified I/O standard values (not recommended), use this command: set_property SEVERITY {Warning} [get_drc_checks NSTD-1]. NOTE: When using the Vivado Runs infrastructure (e.g. launch_runs Tcl command), add this command to a .tcl file and add that file as a pre-hook for write_bitstream step for the implementation run. Problem ports: clk, and led. ERROR: [DRC UCIO-1] Unconstrained Logical Port: 2 out of 2 logical ports have no user assigned specific location constraint (LOC). This may cause I/O contention or incompatibility with the board power or connectivity affecting performance, signal integrity or in extreme cases cause damage to the device or the components to which it is connected. To correct this violation, specify all pin locations. This design will fail to generate a bitstream unless all logical ports have a user specified site LOC constraint defined. To allow bitstream creation with unspecified pin locations (not recommended), use this command: set_property SEVERITY {Warning} [get_drc_checks UCIO-1]. NOTE: When using the Vivado Runs infrastructure (e.g. launch_runs Tcl command), add this command to a .tcl file and add that file as a pre-hook for write_bitstream step for the implementation run. Problem ports: clk, and led. WARNING: [DRC CFGBVS-1] Missing CFGBVS and CONFIG_VOLTAGE Design Properties: Neither the CFGBVS nor CONFIG_VOLTAGE voltage property is set in the current_design. Configuration bank voltage select (CFGBVS) must be set to VCCO or GND, and CONFIG_VOLTAGE must be set to the correct configuration voltage, in order to determine the I/O voltage support for the pins in bank 0. It is suggested to specify these either using the 'Edit Device Properties' function in the GUI or directly in the XDC file using the following syntax: I googled the error and the query gave me 2 answers. The first one looks way way to complicated and to be honest I don't understand it. I got lost at the first step. The second answer is from digilent forums. In there the person asking said he fixed it, and he wrote this; "I solved this. I had input 'clk' in the source and 'CLK' in the constraints file". I am using the constrain file that I donwloaded digilent named "Nexys-4-DDR-Master.xdc" and in the clock I have CLK100MHZ and a commented out one called "clk100mhz". I tried changing in the verilog file to those names instead of clk, since the blinky tutorial said not to modify the constrain file and only uncomment. Please help this is like the most frustrating hello world I ever had to do. I attached my project files and constrain files in case anyone wants to look at it. blinky.zip Nexys-4-DDR-Master.xdc