M. Hamza Öncüer

Thank you very much! The results seem promising 😃.

Hi, I noticed that the ADP2230 supports USB 3.0. In the datasheet, it mentions that it can handle rapid data streaming. Could you provide more information about this, please?

Hi, I gave it a try. I encountered a 'unable to locate package LibQt5SerialPort' warning. After installing the package, I could successfully open the Waveforms application. Thank you for your assistance.

Yes I have tried it. I've installed the waveforms without any errors, but the application doesn't run when I try to open it.

Hi Attila, could you tell me when it will be released for ARM64? The latest version I was able to run is v3.20.1, later versions don't seem to work on the Raspberry Pi 4 or 5.

Hi, I want to use Amplitude Modulation on Z7 using waveform sdk but I did not understand how to do it there are functions in the sdk that shows it is possible but they are not clear. Are there any example code to show how it is done ?

Thank you very much Attila, much appreciated.

Hi, is there a way to add timestamp using waveform sdk ?

Did I understand correctly the screen mode is actually does stream to pc, the record mode on other hand stores the captures to ddram and after the ddram buffer filled it sends the data to the pc is that correct ? I faced another problem the ethernet is actually performed worse than the usb, the pc I attached the z7 supports gigabit ethernet.

Thank you very much, can I understand if the lost or not ? Does it give warning if the the data lost ? What is the maximum adc sampling rate I can choose is I select 128Mi buffer size ?

It is kind of important, I would be glad if someone answer me quickly.

Hi, I want to use acqmodeScanScreen mode but I did not understand how it works exactly, I mean can it do continuous lossless data acquisitions if I select scan screen, 10MHz sampling rate and 128Mi buffer size at z7 ?

I mean can it do continuous lossless data acquisitions if I select scan screen and 10MHz sampling rate and 128Mi buffer size at z7 ?

Hi, I want to use acqmodeScanScreen mode but I did not understand how it works exactly, if I set the buffer to lets say 500 may I do data acquisition continuously without losing data at lets say 10MHZ sampling rate and does reducing buffer size means I can use higher sampling rates for streaming ?

Than you very much, do you planning to add a built in peak finder functionality to waveforms api ?

Thank you very much but I am using Qt/Python and I haven't achieved these high speeds. I believe the problem caused by the python. Can I modify the waveforms api's fpga codes so I can add a peak finding option to waveform api's data acquisition function ?

Thank you but if I understood correctly the example you give takes the whole frame from the board then find the maximum I need to find the maximum within the Z7 then send it to pc, is it possible ?

Thank you very much. Is it possible to take x value of the maximum as well ?

Hi, is it possible to return only the maximum value from an ADC frame? I want to identify the maximum value within the FPGA and then send it to the PC. Can this be done using the WaveForms SDK?"

Hi, Eclypse z7's case fan working too noisy, is it fine to detach it ? As well as I see the fan below the processor doesn't work, Does it activate automatically when the temperature get high ?

Hello, May I use eclipse z7's pmods with the waveforms sdk ? or is there another way to access device IOs ?

it gets the power there is no problem there, I measured the voltages that supposed to be 3.3v and 1.8v but they give 0.4V so I think device gets the power.

I attached the cable to IC20 but nothing changed, also I measured the FB16 and FB6 there are no voltages. What might be the problem what do you think ? Could you help me please.

I measured these values. There are no 3.3V or 1.8V, both of them gives 0.434V. Could FTDI chip be damaged ?

I have seen this post but it didn't help. Are there any other solution to this problem ?