Xilinx Zynq MP First Stage Boot Loader 
Release 2020.1   Nov  2 2022  -  22:32:22
Reset Mode	:	System Reset
Platform: Silicon (4.0), Running on A53-0 (64-bit) Processor, Device Name: XCZU3EG
Digilent Genesys ZU board-specific init
SD1 with level shifter Boot Mode 
Non authenticated Bitstream download to start now
PL Configuration done successfully 
8êŠUjT”'$HPª£ running on XCZU3EG/silicon v4/RTL5.1 at 0xfffea000
NOTICE:  BL31: v2.2(release):xilinx_rebase_v2.2_2020.1
NOTICE:  BL31: Built : 22:28:38, Nov  2 2022


U-Boot 2020.01 (Nov 02 2022 - 22:31:57 +0000)

Board: Xilinx ZynqMP
DRAM:  4 GiB
PMUFW:	v1.1
EL Level:	EL2
Chip ID:	zu3eg
NAND:  0 MiB
MMC:   mmc@ff170000: 0
In:    serial@ff000000
Out:   serial@ff000000
Err:   serial@ff000000
Bootmode: LVL_SHFT_SD_MODE1
Reset reason:	EXTERNAL 
Net:   
ZYNQ GEM: ff0b0000, mdio bus ff0b0000, phyaddr 15, interface rgmii-id
Warning: SPI speed fallback to 100 kHz
SF: Detected is25lp256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
zynq_board_read_rom_ethaddr: SPI ethaddr: 00:18:3E:03:B1:8B

Warning: ethernet@ff0b0000 using MAC address from ROM
eth0: ethernet@ff0b0000
Hit any key to stop autoboot:  2  1  0 
arasan_sdhci_execute_tuning:Tuning failed
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
2007 bytes read in 16 ms (122.1 KiB/s)
## Executing script at 20000000
Error reading cluster
** Unable to read file image.ub **
## Loading kernel from FIT Image at 10000000 ...
Bad FIT kernel image format!
ERROR: can't get kernel image!
SCRIPT FAILED: continuing...
** No partition table - mmc 0 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
## Executing script at 20000000
** No partition table - mmc 0 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
Bad Linux ARM64 Image magic!
SCRIPT FAILED: continuing...
MMC Device 1 not found
no mmc device at slot 1
SF: Detected is25lp256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
Offset exceeds device limit
sf - SPI flash sub-system

Usage:
sf probe [[bus:]cs] [hz] [mode]	- init flash device on given SPI bus
				  and chip select
sf read addr offset|partition len	- read `len' bytes starting at
				          `offset' or from start of mtd
					  `partition'to memory at `addr'
sf write addr offset|partition len	- write `len' bytes from memory
				          at `addr' to flash at `offset'
					  or to start of mtd `partition'
sf erase offset|partition [+]len	- erase `len' bytes from `offset'
					  or from start of mtd `partition'
					 `+len' round up `len' to block size
sf update addr offset|partition len	- erase and write `len' bytes from memory
					  at `addr' to flash at `offset'
					  or to start of mtd `partition'
sf protect lock/unlock sector len	- protect/unprotect 'len' bytes starting
					  at address 'sector'

SCRIPT FAILED: continuing...


no devices available
SCRIPT FAILED: continuing...
starting USB...
Bus dwc3@fe200000: Register 2000440 NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus dwc3@fe300000: Register 2000440 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus dwc3@fe200000 for devices... 1 USB Device(s) found
scanning bus dwc3@fe300000 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device

Device 1: unknown device
scanning bus for devices...

Device 0: unknown device
ethernet@ff0b0000 Waiting for PHY auto negotiation to complete..